Welcome to Miles for Less. Our earth friendly GREEN-MPG fuel saving device will help you save money on gas, reduce toxic emissions, clean your car's engine and more at a price you can afford. Years of dedication to finding earth friendly solutions and a commitment to quality have produced a revolutionary yet simple way to reduce the carbon footprint we make with our cars. We have combined this with great service , and online convenience. Through the Internet, we can provide helpful infomation to support your eco-friendly choices, plus a full money back guarantee on all our products!

Historical / Scientific Introduction

Magnets are simple and inexpensive, and you don't have to be a rocket scientist to figure out how to install them on your water pipes or automobile fuel line. Most importantly, you don't have to break into the lines with a hack saw -- the magnets can be applied to the outside of the lines. However, the polarity of the magnetic installation is generally considered to be very important, and they have to be sufficiently strong for the fields to penetrate into the interior of a fuel line. If the magnets won't literally pinch your fingers (ouch!) they probably aren't strong enough..

When used on fuel lines carrying gasoline, diesel, or other combustible fuels, south-seeking pole magnetic fields generally produce a greater energy yield for a given amount of fuel. Some argue the magnetic treatment of fuels stimulates a more volatile mixture, pushing the phase-change towards the gaseous conditions more quickly than normal, and thereby increasing the efficiency of combustion. The mechanism of these effects is not so well understood, but the effects are reasonably well documented. The polarity of magnetism also has an influence, so one cannot blindly apply magnets to a water or fuel pipe and expect reproducible results.

Years ago, we sold magnetic fuel treatment and water treatment devices which were quite expensive, requiring one to cut into the fuel line of the car, or into the water pipe, to insert the treatment device. Today, we use a simpler and cheaper method which does not require such cutting.  Our small and powerful magnets, can be directly applied to the outside of any fuel or water supply line, secured in place with the provided cable tie. They can be stacked to create even more powerful magnetic fields for larger diameter water or fuel lines. They are a fraction of the cost of the more difficult-to-install, in-line magnetic devices we used to sell, and do not require any cutting of fuel lines or water pipes. We offer these magnets in a set of 2 for $24.95, (one for each side) with full instructions provided. At these prices, you cannot afford not to undertake a modest experimental trial at water treatment and fuel savings. 

In the 1960's, rumors from the farm belt indicated that by placing a small, powerful magnet on the fuel line of an internal combustion engine, gas mileage would be increased. Controlled tests subsequently run by independent testing laboratories have confirmed that this effect is real. A properly constructed and installed magnetic gas treatment unit will increase mileage up to 15%. Informal tests by Natural Energy Works personnel also confirm an increase in mileage, from about 5% to 15% depending upon the type of vehicle, environmental conditions and driver.

As with the magnetic treatment of water, gasoline also appears to have its phase-change behavior altered by magnetic treatment. One theory holds that the gasoline vaporizes more fully under magnetization, allowing a more dispersed and mixed air/fuel mixture. Other theories hold that the electrical ionization of gas droplets is affected, or that the fluid is "activated" or charged in some unknown manner. What we do know is that the magnetic energy increases the combustion ratio to reduce both fuel consumption and air pollution.

Using the instructions provided and with a basic set of our strong but small magnets, you can quickly and easily install a treatment system onto the outside of the fuel line, without the need to cut into or remove any engine parts. The magnets can be used on standard carbureted or fuel-injected gasoline or diesel engines, in Cars, Trucks, RVs, Boats, Buses or Motorcycles. It should not take more than 15 minutes to complete the procedure, and will treat one average-size automobiles,  truck or bus. For residential propane, fuel oil, and natural gas furnaces, stoves and water heaters, you can put the magnets on the outside of the lines in the same way they are used for an automobile. For larger diameter fuel lines, simply increase the magnetic strength by stacking the magnets and applying them to the outside of the fuel line (again, the south-seeking pole faces the fuel line). For such specialized purposes, purchase as many additional sets of magnets as is necessary. Try it risk-free with our 100% money-back guarantee within one year, if you are not satisfied with the results.  Click on the button below to get yours now for only $24.95, shipping and handling included.

Experience Our No Hassle Guarantee!